iFlight BLITZ F7 Pro Flight Controller 35x35mm

iFlight BLITZ F7 Pro V1.1 Flight Controller 35x35mm

Dhs. 253.00
Save Dhs. 99

Quantity

Featured Products

SUNLU ASA 3D Printer Filament 1.75mm 1KG

Dhs. 69.00 Dhs. 88.00

SUNLU PETG 3D Printer Filament 1.75mm 1KG

Dhs. 48.00 Dhs. 53.00

RadioMaster Bandit BR3 ExpressLRS 915MHz ELRS TCXO Receiver

Dhs. 92.00 Dhs. 95.00

RadioMaster TX16S Mark II Max Radio Controller Transmitter

Dhs. 891.00 Dhs. 1,001.00

TBS Crossfire Micro TX V2 Starter Set

Dhs. 396.00 Dhs. 407.00

Infinity 1400mAh 6S 150C 22.2V LiPo Battery XT60 [DG]

Dhs. 110.00

iFlight BLITZ F7 Pro V1.1 Flight Controller 35x35mm

The iFlight BLITZ F722 Pro V1.1 Flight Controller features an improved circuit design, better components, and lower electrical noise. This FC is plug-and-play with DJI and has FC LED indicators, OSD, a 512Mb Black box, and an LC filter.

Features

Improved circuit design, better components, and lower electrical noise!
DJI HD VTX Connector (Plug-and-Play / No soldering required)
FC indicator LEDs for visual debugging
512MB BlackBox
With LC filter
OSD

Specifications

Mounting Pattern: 35*35mm/ 4mm PCB hole diameter
Smartaudio / IRC Tramp VTX protocol supported
Firmware target: IFLIGHT_BLITZ_F7_PRO
Input Voltage: 14.8V-34V (4S-8S LIPO)
Motor outputs: 4x (SH1.25 connector)
Flash: 512MB (Blackbox flash)
I2C serial: SDA / SLA pads
Dimensions: 41*41.5mm
Barometer: DPS310
OSD Chip: AT7456E
LED controller: Yes
MCU: STM32 F722
Weight: 17g (±2)
Beeper pad: Yes
Gyro: BMI270
UARTS: 4

IMPORTANT NOTES

Frsky SmartPort, Tramp & Smartaudio can be connected to any unused UART_TX, we suggest you connect to Uart_TX1
SBUS, CRSF, ELRS, IBUS, DSM ETC... can be connected to any unused UART_RX, we suggest you connect to Uart_RX2
F.port can be connected to any unused UART_TX, we suggest you connect to Uart_TX2
F722 MCU has an inner inverter.

Includes

1x BLITZ F7 Pro V1.1 Flight Controller
1x GH1.25 7pin connector for HD VTX/Analog VTX(RX2/GND/RX1/TX1/GND/+12V/Video out)
1x GH1.25 8pin connector for ESC1 (GND/VBAT/M1/M2/M3/M4/CUR/RX5)
1x GH1.25 8pin connector for ESC2 (GND/VBAT/M5/M6/M7/M8/CUR/RX5)
1x GH1.25 4pin connector for GPS&Mag(+5V/GND/TX4/RX4/SDA/SCL)
1x GH1.25 3pin connector for Analog camera (Video in/GND/+5V)
1x GH1.25 4pin connector for Any Receiver(GND/+5V/RX2/TX2)
1x GH1.25 4pin connector for LED & Buzzer(LED/BZ-/+5V/GND)
1x 4-Pin USB-C Extender Adapter Board
4x Silicone Grommets